<optgroup id="eklfg"><li id="eklfg"></li></optgroup>
<legend id="eklfg"></legend><track id="eklfg"><i id="eklfg"></i></track>

  • <span id="eklfg"><sup id="eklfg"></sup></span>
    1. <span id="eklfg"><sup id="eklfg"></sup></span>
    2. 021-39965029
      上海世銳電子科技有限公司
      181-17506350

      產品中心

      CA ISO CALIBRATION SET FOR AUTOMOTIVE TRANSIENTS
      • 應用領域
      • 符合下列標準
      • 特點
      • 軟件
      • 優點
      • 點擊下載
      2.jpg
      • 應用領域-1
        應用領域

        filename

        返回
      • 符合下列標準-1
        符合下列標準

        > ISO 16750-2

        > ISO 7637-1:1990

        > ISO 7637-2:1990

        > ISO 7637-2:2004

        > ISO 7637-2:2011


        返回
      • 特點-1
        特點

        > One single load resistor box

        > Includes all required load resistor values

        > Highly accurate resistors (+/-1%)

        > High temperature stability

        > Resistors with very low inductance

        > Resistor values 0.5ohm, 1ohm, 2ohm, 4ohm,

        10ohm, 20ohm and 50ohm


        返回
      • 軟件-1
        軟件

        The CA ISO verification box is directly plugged into the

        CDN outputs of the transient generator. The required load

        resistor is selected by the bridge connector. The waveform

        across the load resistor is best measured by a 100:1

        voltage probe with sufficient bandwidth and voltage

        capability. EM TEST recommend a bandwidth of 20MHz

        minimum and a voltage measuring capability of 1,000V


        返回
      • 優點-1
        優點

        SELECTION OF LOAD RESISTORS

        The set of load resistors has been well selected in order to

        meet the wide range of source resistors specified in

        various national/international standards and vehicle

        manufacturer specifications.

        The following load resistors are most used:

        0.5 Ohm for Load Dump pulse verification as per a number

        of manufacturer specifications

        1.0 Ohm for Load Dump pulse verification as per a number

        of manufacturer specifications

        2.0 Ohm for verification of pulse 2a and pulse 5 as per ISO

        7637-2 and various manufacturer specifications

        4.0 Ohm for verification of pulses 1, 2 and Load Dump

        pulse 5 as per various manufacturer specifications

        10.0 Ohm for verification of pulses 1 and 2 as per ISO

        7637-2 and various manufacturer specifications

        20.0 Ohm for verification of pulse 1 as per ISO 7637-2 and

        various manufacturer specifications.

        All load resistors are non-inductive and have a tolerance

        better than 1% as per standard requirements. They show

        sufficient power dissipation for the transient pulse energy.


        返回
      • 點擊下載-1
        點擊下載

        返回
      文件下載
      文本對象
      文本對象
      郵件 haifa.yang@emctest-sr.com
      QQ客服 376400163
      電話熱線 021-39965029
       
      av网址在线

      <optgroup id="eklfg"><li id="eklfg"></li></optgroup>
      <legend id="eklfg"></legend><track id="eklfg"><i id="eklfg"></i></track>

    3. <span id="eklfg"><sup id="eklfg"></sup></span>
      1. <span id="eklfg"><sup id="eklfg"></sup></span>